CAT 5 DUPLEX BOOSTER PUMP WITH TANK

HOME  | PUMPS | BOOSTER PUMPS WITH TANKS | CAT 5 DUPLEX

CAT 5 Break Tank Booster - Duplex

Duplex CAT 5 Booster Pumps with tanks

Twin booster set designed to supply from a Cat 5 water storage tank and to provide varying pressures & flows.

The supply of Cat 5 cold water to :

Hygienic Rooms, Laboratories, Veterinary Surgeries, Garden irrigation, Bib taps, Bin stores, Abattoirs, Mortuaries, Multi-story window wash, Hotels, Apartments

Pump

Type: Horizontal multistage

All parts in contact with fluid are stainless steel. Single phase 230V or Three phase 400V 50 Hz motors up to and including 2.2 Kw.

Break Tank

Bespoke Poly & GRP tanks available in varying sizes.

Complete with raised ball valve chamber with weir overflow to CAT 5 type AB air gap regulations (CAT 4 Type Air Gap available on request).

Variable Speed Operation

The Fluid Controller is designed to start the pump when the system pressure falls, upon start up the unit continues to pump at a constant pressure to keep up with demand. The system pressure is monitored by a transducer and the pump will run at the speed required at any given time to keep up with the varying demand. Should there be a lack of water, the fluid controller has dry run protection and will go into fault to protect the pump. There is also a facility to connect an external float to protect the pump as well. The controller also has a facility to have “volt free contacts” for any BMS system if a fault occurs.

Digital Display: LCD display with full operating parameters and alarm log.

 

Below are typical examples and prices of our Duplex range Break Tank and Booster Sets. Our Duplex booster sets can be configured to meet your exact requirements. Please contact us for more information.

Example Booster Set 1
Duty: 1.9 l/sec @ 3.0 Bar (each pump capable of 1.9 l/sec @ 3.0 Bar)
Operation mode:Duty / Stand-by Variable Speed Controlled
Supply:230v~1ph~50hz
Booster set model:SP2V-5HM06S-MT/24-AGAP501 (Tank mounted at side of set)
Pump type:2 x 5HM06S11T horizontal multi-stage pumps manufactured in 304 stainless steel, WRAS approved, complete with 1.1 kw 230v~3ph~50hz IP55 motors
Suction Manifold:2” AISI 304 stainless steel – connected to break tank
Discharge Manifold:1½” AISI 304 stainless steel – Terminating in BSP (M) connection.
Suction & Discharge valves:Brass Isolation Ball Valve to each pump suction & discharge.
Controls:2 x E-SERES Variable Speed Controller mounted in discharge pipework complete with LCD display to indicate system overview and operating parameters. Complete with automatic changeover of duty pump, volt free contacts for remote alarm and provision for wiring of low level float switch. Built in protection against dry running, over current and over temperature.
Panel:Plastic consumer unit
Vessel(s):24 litre 10 bar vessel mounted on discharge manifold.
Base:Powder coated welded steel base with tank mounted at the side of the set complete with interconnecting pipe & valve.
Break Tank Details:FWS 501 litres nominal capacity one piece WRAS approved insulated GRP cold water storage tank, complete with: Insulated Sealed Cover and access manway, 42 mm combi-screen overflow, warning overflow and all associated fittings. The tank is fitted with a weir overflow complete with 1” equilibrium ball valve with drop arm to CAT 5 AB Airgap specification.
Total Price: £5639.76

Example Booster Set 2
Duty: 1.9 l/sec @ 3.0 Bar (each pump capable of 1.9 l/sec @ 3.0 Bar)
Operation mode:Duty / Stand-by Variable Speed Controlled
Supply:230v~1ph~50hz
Booster set model:SP2V-5HM06S-MT/24-AGAP1000 (Tank mounted at side of set)
Pump type:2 x 5HM06S11T horizontal multi-stage pumps manufactured in 304 stainless steel, WRAS approved, complete with 1.1 kw 230v~3ph~50hz IP55 motors.
Suction Manifold:2” AISI 304 stainless steel – connected to break tank.
Discharge Manifold:1½” AISI 304 stainless steel – Terminating in BSP (M) connection.
Suction & Discharge valves:Brass Isolation Ball Valve to each pump suction & discharge
Controls:2 x E-SERES Variable Speed Controller mounted in discharge pipework complete with LCD display to indicate system overview and operating parameters. Complete with automatic changeover of duty pump, volt free contacts for remote alarm and provision for wiring of low level float switch. Built in protection against dry running, over current and over temperature
Panel:Plastic consumer unit
Vessel(s):24 litre 10 bar vessel mounted on discharge manifold.
Base:Powder coated welded steel base with tank mounted at the side of the set complete with interconnecting pipe & valve.
Break Tank Details:FWS 1000 litres nominal capacity one piece WRAS approved insulated GRP cold water storage tank, complete with: Insulated Sealed Cover and access manway, 42 mm combi-screen overflow, warning overflow and all associated fittings. The tank is fitted with a weir overflow complete with 1” equilibrium ball valve with drop arm to CAT 5 AB Airgap specification.
Total Price:£5976.00

Example Booster Set 3
Duty: 1.9 l/sec @ 3.0 Bar (each pump capable of 1.9 l/sec @ 3.0 Bar)
Operation mode:Duty / Stand-by Variable Speed Controlled
Supply:230v~1ph~50hz
Booster set model:SP2V-5HM06S-MT/24-AGAP1501 (Tank mounted at side of set)
Pump type:2 x 5HM06S11T horizontal multi-stage pumps manufactured in 304 stainless steel, WRAS approved, complete with 1.1 kw 230v~3ph~50hz IP55 motors.
Suction Manifold:2” AISI 304 stainless steel – connected to break tank.
Discharge Manifold:1½” AISI 304 stainless steel – Terminating in BSP (M) connection.
Suction & Discharge valves:Brass Isolation Ball Valve to each pump suction & discharge
Controls:2 x E-SERES Variable Speed Controller mounted in discharge pipework complete with LCD display to indicate system overview and operating parameters. Complete with automatic changeover of duty pump, volt free contacts for remote alarm and provision for wiring of low level float switch. Built in protection against dry running, over current and over temperature
Panel:Plastic consumer unit
Vessel(s):24 litre 10 bar vessel mounted on discharge manifold.
Base:Powder coated welded steel base with tank mounted at the side of the set complete with interconnecting pipe & valve.
Break Tank Details:FWS 1501 litres nominal capacity one piece WRAS approved insulated GRP cold water storage tank, complete with: Insulated Sealed Cover and access manway, 42 mm combi-screen overflow, warning overflow and all associated fittings. The tank is fitted with a weir overflow complete with 1” equilibrium ball valve with drop arm to CAT 5 AB Airgap specification.
Total Price:£6527.52

Duplex Break Tank Booster - Image 1
Duplex Break Tank Booster - Image 2
Duplex Break Tank Booster - Image 3

3HMS Range

5HMS Range

10HMS Range

Need Help?

We can advise on the correct pump for your requirements.
Please contact us on
01629 363311

we are more than happy to help.